Put the Jeep Wrangler in neutral by pushing the shifter down into the neutral position.
If your Jeep Wrangler has a dead battery, you can put it in neutral by:
1. Locate the battery under the hood.
2. Disconnect the negative terminal from the battery.
3. Lift up on the floor mat to access the shifter.
4. Put the shifter in the neutral position.
5. Reconnect the negative terminal to the battery.
If your Jeep Wrangler has an automatic transmission, you can also put it in neutral by:
1. Locate the battery under the hood.
2. Disconnect the negative terminal from the battery.
3. Lift up on the floor mat to access the shifter.
4. Put the shifter in the Park position.
5. Start the Jeep and let it idle for a few minutes.
6. Turn off the Jeep and disconnect the negative terminal from the battery again.
7. Put the shifter in the neutral position.
8. Reconnect the negative terminal to the battery.
How Do You Put A Jeep Wrangler In Neutral With A Dead Battery?
You can’t put a Jeep Wrangler in neutral with a dead battery.
If you find yourself with a dead battery in your Jeep Wrangler, don’t panic! Follow these simple steps and you’ll be back on the road in no time.
1. Open the hood and locate the battery.
2. Using a wrench or pliers, loosen the negative (-) terminal clamp and remove the cable from the battery post.
3. Do the same for the positive (+) terminal.
4. With the terminals disconnected, put the transmission in neutral.
5. Push the Wrangler a few feet to get it out of the way of traffic.
Now that you’re safely out of the way, it’s time to jump start your Jeep.
1. Connect one end of the positive jumper cable to the positive terminal of the dead battery.
2. Connect the other end of the positive cable to the positive terminal of the good battery.
3. Connect one end of the negative jumper cable to the negative terminal of the good battery.
4. Finally, connect the other end of the negative cable to a metal ground on the Wrangler, such as a bolt on the engine block.
5. Start the engine of the car with the good battery and let it run for a few minutes.
6. Try starting the Jeep Wrangler. If it doesn’t start, check the connections and make sure the cables are connected to the correct terminals.
Once your Jeep is running, be sure to drive it for a while to recharge the battery. And that’s it! You’re back on the road.
Is It Possible To Put A Jeep Wrangler In Neutral With A Dead Battery?
Yes, it is possible to put a Jeep Wrangler in neutral with a dead battery.
If your Jeep Wrangler won’t start, it might just be that the battery
Is dead. But is it possible to put a Jeep Wrangler in neutral with a dead battery?
Here’s how to do it:
1. Open the hood and locate the battery.
2. Disconnect the negative terminal first, then the positive terminal.
3. Locate the transmission shift lever and move it to the neutral position.
4. Reconnect the battery terminals, positive first, then negative.
5. Start the engine and enjoy the ride!
FAQ
How Do You Safely Put A Jeep Wrangler In Neutral With A Dead Battery?
1. Park the Jeep Wrangler on a level surface and set the parking brake.
2. Shift the Jeep Wrangler into first gear.
3. Turn the Jeep Wrangler’s ignition key to the “On” position, but do not start the engine.
4. Press and release the Jeep Wrangler’s clutch pedal slowly.
5. While holding the clutch pedal down, shift the Jeep Wrangler into neutral.
6. Turn the Jeep Wrangler’s ignition key to the “Off” position.
7. Release the Jeep Wrangler’s clutch pedal.
What Are The Steps To Put A Jeep Wrangler In Neutral With A Dead Battery?
1. With the Jeep Wrangler turned off, set the parking brake.
2. Shift the Jeep Wrangler into second gear.
3. Start the Jeep Wrangler and release the clutch slowly while pressing the accelerator.
4. When the Jeep Wrangler reaches approximately 5 mph, shift into neutral.
5. Turn off the Jeep Wrangler and set the parking brake.
Conclusion
If your Jeep Wrangler’s battery is dead, you can put it in neutral by disconnecting the battery, then connecting the Positive (+) cable to the Positive (+) terminal on the starter, and the Negative (-) cable to the ground.
If you’re still having trouble after reading this, feel free to ask a question in the comments section below.